Thinking Diver

Where divers think about stuff


Dive-computers Reviews – Part One – the Delta-P VR3

by Erik Dasque

Experience

As you may know by now, I dive an eCCR, a life support system which purported goal is to attempt to kill me when I won’t be watching. I was taught to watch though and that means monitor my PPO2 (Oxygen Partial Pressure) frequently. Like any O2ptima rebreather diver, I have a primary on my left wrist that I can check for PO2 as well as a heads up display (the HUD is driven by the secondary handset, which is tucked away in a belt pouch) both of which read from three same oxygen sensor. When I was told about the possibility to add a third computer to the lot which would monitor a fourth cell as well as give me a redundant source of deco information, I jumped on it.

I already owned a Delta-P VR3 which was compatible with this setup. As I was taking my Advanced Nitrox and Deco class years before, I had been co-erced into buying a deco-capable dive computer. The VR3 seemed wonderful with its expandability. And in truth it was.

Delta-P Vr3 Decompression Computer

The Delta-P VR3 is a beast of a dive computer, looking more adept at breaking a lobster shell around a beach fire than being attached on a human wrist. It feels and looks solid if somewhat antiquated. Its main selling point at the time is that you could upgrade it as needed going from Nitrox diving to Trimix, Open Circuit to CCR, Bullman to VPM. And that’s exactly what I did with it, ending up paying around $2000 for the whole getup.

I want to say that the VR3 served me well over the year but that wouldn’t really be true. On my first Open Circuit deco dive, on the deck of the German U-Boat U853, the brand new VR3 suddenly shut off, its screen displaying no information, therefore engraining into my brain that backup tables compulsory. The culprit was supposedly the AA battery I was using instead of a leaner but supposedly compatible european LR6. During the 10-15 hours of my CCR training, it performed beautifully but for the next 5 dives, it would shut off occasionally, complain about low battery or think it was underwater, missing stops, while I was driving to the dive site. It was a backup computer I had learnt to not count on which defeats the purpose. But then again, for 20 hours of CCR diving in the Bahamas, it worked without any issue.

You probably will ask why I never sent it back ? Well, it mostly worked … and the factory is back in the UK and charges quite a bit of money for an overhaul.

I think another reason though is that I knew it wouldn’t be my computer for long. You see, the main issue I have with the VR3 is that it probably has the worse user interface I have ever seen. I might not remember much from my MS-DOS days but it must have been conceived then. Most VR3 users will tell me they find it intuitive but I think they just got used to it. No one can pick up a VR3 and use it immediately. After a few weeks out of the water, I would often forget how to calibrate it, how to set the bailout gases, change the screen orientation. Simple operations such as turning gases on and off or setting them up take a long time and shouldn’t.

Blinded by the fact that I wanted my buddy Sam to use the same gear configuration I had, I even tried to convince him to buy a VR3. He wouldn’t have none of it and he was right. So he went and bought a Liquivision X1. More on that later.

Pros and Cons

Let’s look at the VR3, objectively:

  • Solid piece of equipment
  • Bulky, oddly shaped
  • Deco Algorithms: Bulman or optionally VPM ($)
  • _very_ conservative, ‘won’t get you bent’
  • User interface is far from user friendly
  • Can be purchased bare (Nitrox Open Circuit, Monochrome) then upgraded (Trimix, CCR, Color) as you need it
  • External PPO2 (CCR), Wired High Pressure Sensor, O2 Analyser options
  • Downloadable dive log option is expensive and software is antiquated at best
  • Readability is decent but not outstanding. New HD screen doesn’t seem to be much of an improvment
  • Batteries are end-user swappable but picky in real life
  • Firmware is not user upgradable and requires sending back to the factory (and is not free)
  • Can probably pick up a used one for cheap on ebay or one of the tech divers forums

Conclusion

Should you buy a VR3 today ? Probably not. While Delta-P recently released an updated model (the VR3 HD) the software isn’t much better and the screen readability hasn’t improved much. The VR3 was one of the best dive computers in the early 2000 but newer better computers have recently been introduced (Shearwater Pursuit and Liquivision X1 are fine examples). Delta P themselves have a new computer, the VRX with a new form factor and deco algorithm. So if you’re in the market for something great, pass on the VR3. But if you’re on a tight budget, don’t mind buying a used computer, the VR3 is a solid decompression computer.

Why did I bother reviewing the VR3 you may ask ? Even though it’s becoming the grandfather of modern day deco computers, the VR3 is relevant. It’s a yardstick if you will, something new computers will be judged against because there are tens of thousands of old VR3s out there. And with the Liquivision X1, Shearwater Pursuit and upcoming Dive Rite Nitek X, I for one am looking forward to trying them all out.

Next…

The Liquivision X1 deco computer and its PPO2 interface, the X-link

Disclaimer: A decompression computer is not a substitute for planning your dive and carrying decompression tables. Plan your dive, dive your plan and carry backups tables.




Explore Recent


Last 5 posts by Erik Dasque

47 queries. 0.318 seconds.
53 queries. 0.359 seconds. Real Time Web Analytics